Design Of Shafts

Design Of Shafts

Shaft:

        A shaft is a rotating machine element which is used to transmit power from one place to another. The power is delivered to the shaft by some tangential force and the resultant torque (or twisting moment) set up within the shaft permits the power to be transferred to various machines linked up to the shaft.

Types of Shafts:

The following two types of shafts are important from the subject point of view :

1. Transmission shafts: These shafts transmit power between the source and the machines absorbing power. The counter shafts, line shafts, over head shafts and all factory shafts are transmission shafts. Since these shafts carry machine parts such as pulleys, gears etc., therefore they are subjected to bending in addition to twisting.

2. Machine shafts: These shafts form an integral part of the machine itself. The crank shaft is an example of machine shaft.

Material Used for Shafts:

The material used for shafts should have the following properties :

1. It should have high strength.

2. It should have good machinability.

3. It should have low notch sensitivity factor.

4. It should have good heat treatment properties.

5. It should have high wear resistant properties.

Standard Sizes of Transmission Shafts

The standard sizes of transmission shafts are :

25 mm to 60 mm with 5 mm steps; 60 mm to 110 mm with 10 mm steps ; 110 mm to 140 mm with 15 mm steps ; and 140 mm to 500 mm with 20 mm steps. The standard length of the shafts are 5 m, 6 m and 7 m.

Design of Shafts

The shafts may be designed on the basis of

1. Strength, and 2. Rigidity and stiffness.

In designing shafts on the basis of strength, the following cases may be considered :

(a) Shafts subjected to twisting moment or torque only,

(b) Shafts subjected to bending moment only,

(c) Shafts subjected to combined twisting and bending moments, and

(d) Shafts subjected to axial loads in addition to combined torsional and bending loads.

Shafts Subjected to Twisting Moment Only

When the shaft is subjected to a twisting moment (or torque) only, then the diameter of the shaft may be obtained by using the torsion equation. We know that

WATCH THIS VIDEO FOR DESIGN OF SHAFTS SUBJECTED TO TWISTING MOMENT ONLY


Example 1. A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The shaft may be assumed to be made of mild steel with an allowable shear stress of 42 MPa. Determine the diameter of the shaft, neglecting the bending moment on the shaft.
Solution:

WATCH THIS VIDEO FOR SOLUTION



Example 2. A solid shaft is transmitting 1 MW at 240 r.p.m. Determine the diameter of the shaft if the maximum torque transmitted exceeds the mean torque by 20%. Take the maximum allowable shear stress as 60 MPa.
Solution:

WATCH THIS VIDEO FOR SOLUTION



Example 3. Find the diameter of a solid steel shaft to transmit 20 kW at 200 r.p.m. The ultimate shear stress for the steel may be taken as 360 MPa and a factor of safety as 8. If a hollow shaft is to be used in place of the solid shaft, find the inside and outside diameter when the ratio of inside to outside diameters is 0.5.
Solution:

WATCH THIS VIDEO FOR SOLUTION




Shafts Subjected to Bending Moment Only

When the shaft is subjected to a bending moment only, then the maximum stress (tensile or
compressive) is given by the bending equation. We know that

WATCH THIS VIDEO FOR DESIGN OF SHAFTS SUBJECTED TO BENDING MOMENT ONLY



Example 4. A pair of wheels of a railway wagon carries a load of 50 kN on each axle box, acting at a distance of 100 mm outside the wheel base. The gauge of the rails is 1.4 m. Find the diameter of the axle between the wheels, if the stress is not to exceed 100 MPa.
Solution:

WATCH THIS VIDEO FOR SOLUTION



Shafts Subjected to Combined Twisting Moment and Bending Moment

When the shaft is subjected to combined twisting moment and bending moment, then the shaft must be designed on the basis of the two moments simultaneously. Various theories have been suggested to account for the elastic failure of the materials when they are subjected to various types of combined stresses. The following two theories are important from the subject point of view :
1. Maximum shear stress theory or Guest's theory. It is used for ductile materials such as mild steel.
2. Maximum normal stress theory or Rankine’s theory. It is used for brittle materials such as cast iron.

WATCH THIS VIDEO FOR DESIGN OF SHAFTS SUBJECTED TO COMBINED TWISTING & BENDING MOMENT



Example 5. A solid circular shaft is subjected to a bending moment of 3000 N-m and a torque of 10 000 N-m. The shaft is made of 45 C 8 steel having ultimate tensile stress of 700 MPa and a ultimate shear stress of 500 MPa. Assuming a factor of safety as 6, determine the diameter of the shaft.
Solution:

WATCH THIS VIDEO FOR SOLUTION




 END 

Post a Comment

0 Comments